Showing 13–24 of 261 results

Show sidebar
Show 9 24 36
Filters
Close

3TSSI SOLAR PUMP

1.APPLICATION AREA: This project products are mainly used in dry region for irrigation of agriculture, It can be used for drinking water and living water. The living condition could be much improved. It also can be used for fountains. 2.MATERIAL OF PARTS: Outlet: stainless steel Pump body: stainless steel Motor body: stainless steel Bearing: C&U 3.ADVANCED TECHNOLOGY: 1.Application innovation Compared with the traditional alternating current machine, the efficiency is improved 25% by the permanent magnetism, direct current, brushless, non-sensor motor. 2.Technics innovation Adopt double plastic package for rotor and stator, motor insulation≥300MΩ, the motor security was much improved. 3.Structure innovation Oil filling, convenient installation and environmental protection 4.HIGHLIGHTS a.Energy-saving and environment-protected green products b.High technique products adopting MPPT and DSP chip technique. c.100% copper wire, cold-rolled silicon steel sheet d.CE certificate e.Advanced three phase brushless DC motor f.Stainless steel 316 screws g.3 years warranty 5.PRINCIPLE OF OPERATION: Solar panel collects sunlight→DC electricity energy → solar controller(rectification,stabilization,amplification,filtering)→available DC electricity→(charge the batteries)→pumping water 6.ADVANTAGES OF SOLAR PUMP SYSTEM: A.It is easier and more widely used than any other dynamoelectric driven pumps. B.It is more economical and more environmentally friendly. 7.MODEL SELECTION: a.The power of solar panel = power of pump ×1.3 The voltage of solar panel = the voltage of pump The controller should be matched b.Select the batteries according to the following formulas: The use hour of battery = The battery capacity ÷(the machine power÷the battery voltage)×0.6 For example,the machine power is 200W, the battery capacity is 100AH,the voltage is 12V,and the battery is fully charged,then the use hour is:100÷(200÷12)×0.6=3.6hours c.The battery capacity= the use hour ÷0.6×(the machine power÷the battery voltage) For example,the machine power is 200W,the battery voltage is 12V,and the battery need to be used for 3.6hours,then the battery capacity is:3.6÷0.6×（200÷12）=100AH
Add to wishlist
Read more
Quick view
Close

4SE(m) 4’’ Deep Well Pump

Performance Range Max. Flow: 22m3/h Max. Head: 480m Application Limits 1. Max. ambient temperature < 40℃; 2. Sand content(in mass fraction)up to 0.01%; 3. hydrogen sulfide content up to 1.5mg/L, chloride ion content up to 400mg/L; 4. pH 6.5 to 8.5; 5. Maximum: 70m below the static water table. Certificate Application Fields 1. Building/construction work/domestic water supply; 2. Irrigation and small water work; 3. Landscaping; 4. Water conservancy system; 5. Factory. Features 1. Edible oil filled motor, stable& reliable running with pressure regulating membrane; 2. Single phase motor with built in B Grade oil proofed capacitor &thermal mode protector; 3. Available with cable with a motor plug, disassemble conveniently; 4. Available with pump casing with plug, 2~8 m3/hrs series with single stage floating impellers, 10~16m3/hrs series with integrated stage floating impellers; 5. Installation in 4" or larger boreholes; Optional Available On Request Oil chamber is available with brass or SS304; Discharge chamber, Inlet parts are available SS304.
Add to wishlist
Read more
Quick view
Close

4SG(m) 4’’ Deep Well Pump

Performance Range
Max. Flow: 22m3/h Max. Head: 454m
Application Limits 1. Max. ambient temperature < 40℃; 2. Sand content(in mass fraction)up to 0.01%; 3. hydrogen sulfide content up to 1.5mg/L, chloride ion content up to 400mg/L; 4. pH 6.5 to 8.5; 5. Maximum: 70m below the static water table.Certificate Application Fields 1. Building/construction work/domestic water supply; 2. Irrigation and small water work; 3. Landscaping; 4. Water conservancy system; 5. Factory. Features 1.Edible oil filled motor, stable& reliable running with pressure regulating membrane; 2.Single phase motor with built in B Grade oil proofed capacitor &thermal mode protector; 3.Available with cable with a motor plug, disassemble conveniently; 4.Available with pump casing with plug, 2~8 m3/hrs series with single stage floating impellers, 10~16m3/hrs series with integrated stage floating impellers; 5.Installation in 4" or larger boreholes; Optional Available On Request Oil chamber is available with brass or SS304; Discharge chamber, Inlet parts are available with casting.
Add to wishlist
Read more
Quick view
Close

4SS 4’’ Deep Well Pump

Performance Range
Max. Flow: 10.8m3/h Max. Head: 330m
Application Limits
1. Max. ambient temperature < 40℃; 2. Sand content(in mass fraction)up to 0.01%; 3. hydrogen sulfide content up to 1.5mg/L, chloride ion content up to 400mg/L; 4. pH 6.5 to 8.5; 5. Maximum: 70m below the static water table.Certificate Application Fields 1. Building/construction work/domestic water supply; 2. Irrigation and small water work; 3. Landscaping; 4. Water conservancy system; 5. Factory. Features 1. Edible oil filled motor, stable& reliable running with pressure regulating membrane; 2. Single phase motor equipped with start box which built in capacitor ¤t mode thermal protector, convenient for replacement; 3. Available with stainless steel pump head, effective against the corrosion and abrasive wear; 4. Installation in 4" or larger boreholes. Optional Available On Request Pipe connection of discharge chamber is available with 1.25", 1.5", 2".
Add to wishlist
Read more
Quick view
Close

4TSC Solar Pump

1.APPLICATION AREA: This project products are mainly used in dry region for irrigation of agriculture, It can be used for drinking water and living water. The living condition could be much improved. It also can be used for fountains. 2.MATERIAL OF PARTS: Outlet: stainless steel Pump body: stainless steel Motor body: stainless steel Bearing: C&U 3.ADVANCED TECHNOLOGY: 1.Application innovation Compared with the traditional alternating current machine, the efficiency is improved 25% by the permanent magnetism, direct current, brushless, non-sensor motor. 2.Technics innovation Adopt double plastic package for rotor and stator, motor insulation≥300MΩ, the motor security was much improved. 3.Structure innovation Oil filling, convenient installation and environmental protection 4.HIGHLIGHTS a.Energy-saving and environment-protected green products b.High technique products adopting MPPT and DSP chip technique. c.100% copper wire, cold-rolled silicon steel sheet d.CE certificate e.Advanced three phase brushless DC motor f.Stainless steel 316 screws g.3 years warranty 5.PRINCIPLE OF OPERATION: Solar panel collects sunlight→DC electricity energy → solar controller(rectification,stabilization,amplification,filtering)→available DC electricity→(charge the batteries)→pumping water 6.ADVANTAGES OF SOLAR PUMP SYSTEM: A.It is easier and more widely used than any other dynamoelectric driven pumps. B.It is more economical and more environmentally friendly. 7.MODEL SELECTION: a.The power of solar panel = power of pump ×1.3 The voltage of solar panel = the voltage of pump The controller should be matched b.Select the batteries according to the following formulas: The use hour of battery = The battery capacity ÷(the machine power÷the battery voltage)×0.6 For example,the machine power is 200W, the battery capacity is 100AH,the voltage is 12V,and the battery is fully charged,then the use hour is:100÷(200÷12)×0.6=3.6hours c.The battery capacity= the use hour ÷0.6×(the machine power÷the battery voltage) For example,the machine power is 200W,the battery voltage is 12V,and the battery need to be used for 3.6hours,then the battery capacity is:3.6÷0.6×（200÷12）=100AH
Add to wishlist
Read more
Quick view
Close

5000W Air-cooled Generator Set

5000W Air-cooled Generator Set
Add to wishlist
Read more
Quick view
Close

5000w Single Phase

5000w Single Phase Air-cooled Generator Set
Add to wishlist
Read more
Quick view
Close

5TSC Solar Pump

1.APPLICATION AREA: This project products are mainly used in dry region for irrigation of agriculture, It can be used for drinking water and living water. The living condition could be much improved. It also can be used for fountains. 2.MATERIAL OF PARTS: Outlet: stainless steel Pump body: stainless steel Motor body: stainless steel Bearing: C&U 3.ADVANCED TECHNOLOGY: 1.Application innovation Compared with the traditional alternating current machine, the efficiency is improved 25% by the permanent magnetism, direct current, brushless, non-sensor motor. 2.Technics innovation Adopt double plastic package for rotor and stator, motor insulation≥300MΩ, the motor security was much improved. 3.Structure innovation Oil filling, convenient installation and environmental protection 4.HIGHLIGHTS a.Energy-saving and environment-protected green products b.High technique products adopting MPPT and DSP chip technique. c.100% copper wire, cold-rolled silicon steel sheet d.CE certificate e.Advanced three phase brushless DC motor f.Stainless steel 316 screws g.3 years warranty 5.PRINCIPLE OF OPERATION: Solar panel collects sunlight→DC electricity energy → solar controller(rectification,stabilization,amplification,filtering)→available DC electricity→(charge the batteries)→pumping water 6.ADVANTAGES OF SOLAR PUMP SYSTEM: A.It is easier and more widely used than any other dynamoelectric driven pumps. B.It is more economical and more environmentally friendly. 7.MODEL SELECTION: a.The power of solar panel = power of pump ×1.3 The voltage of solar panel = the voltage of pump The controller should be matched b.Select the batteries according to the following formulas: The use hour of battery = The battery capacity ÷(the machine power÷the battery voltage)×0.6 For example,the machine power is 200W, the battery capacity is 100AH,the voltage is 12V,and the battery is fully charged,then the use hour is:100÷(200÷12)×0.6=3.6hours c.The battery capacity= the use hour ÷0.6×(the machine power÷the battery voltage) For example,the machine power is 200W,the battery voltage is 12V,and the battery need to be used for 3.6hours,then the battery capacity is:3.6÷0.6×（200÷12）=100AH
Add to wishlist
Read more
Quick view
Close

5TSS Solar Pump

1.APPLICATION AREA: This project products are mainly used in dry region for irrigation of agriculture, It can be used for drinking water and living water. The living condition could be much improved. It also can be used for fountains. 2.MATERIAL OF PARTS: Outlet: stainless steel Pump body: stainless steel Motor body: stainless steel Bearing: C&U 3.ADVANCED TECHNOLOGY: 1.Application innovation Compared with the traditional alternating current machine, the efficiency is improved 25% by the permanent magnetism, direct current, brushless, non-sensor motor. 2.Technics innovation Adopt double plastic package for rotor and stator, motor insulation≥300MΩ, the motor security was much improved. 3.Structure innovation Oil filling, convenient installation and environmental protection 4.HIGHLIGHTS a.Energy-saving and environment-protected green products b.High technique products adopting MPPT and DSP chip technique. c.100% copper wire, cold-rolled silicon steel sheet d.CE certificate e.Advanced three phase brushless DC motor f.Stainless steel 316 screws g.3 years warranty 5.PRINCIPLE OF OPERATION: Solar panel collects sunlight→DC electricity energy → solar controller(rectification,stabilization,amplification,filtering)→available DC electricity→(charge the batteries)→pumping water 6.ADVANTAGES OF SOLAR PUMP SYSTEM: A.It is easier and more widely used than any other dynamoelectric driven pumps. B.It is more economical and more environmentally friendly. 7.MODEL SELECTION: a.The power of solar panel = power of pump ×1.3 The voltage of solar panel = the voltage of pump The controller should be matched b.Select the batteries according to the following formulas: The use hour of battery = The battery capacity ÷(the machine power÷the battery voltage)×0.6 For example,the machine power is 200W, the battery capacity is 100AH,the voltage is 12V,and the battery is fully charged,then the use hour is:100÷(200÷12)×0.6=3.6hours c.The battery capacity= the use hour ÷0.6×(the machine power÷the battery voltage) For example,the machine power is 200W,the battery voltage is 12V,and the battery need to be used for 3.6hours,then the battery capacity is:3.6÷0.6×（200÷12）=100AH
Add to wishlist
Read more
Quick view
Close

6.8 MVA MV | 6.25 MVA MV Turnkey Station Central Inverter

High Yield

  • 3-level technology, inverter max. efficiency 99%
  • High DC/AC ratio up to 1.5

Easy O&M

  • Integrated current and voltage monitoring function for online analysis and trouble shooting
  • Modular design, easy for maintenance
  • Convenient external LCD

Saved Investment

  • Easy transportation and installation due to standard container design
  • Night Static Var Generator (SVG) function

Grid Support

  • Compliance with standards: IEC 61727, IEC 62116
  • Reactive & active power control
  • Low/High voltage ride through (L/HVRT), Frequency ride through (FRT)
 
Download 6.8 MVA MV Turnkey Station Datasheet PDF
Download 6.25 MVA MV Turnkey Station Datasheet PDF
Add to wishlist
Read more
Quick view
Close

6SE 6’’ Deep Well Pump

Performance Range
Max. Flow: 60m3/h Max. Head: 448m Application Limits 1. Max. ambient temperature < 40℃; 2. Sand content(in mass fraction)up to 0.01%; 3. hydrogen sulfide content up to 1.5mg/L, chloride ion content up to 400mg/L; 4. pH 6.5 to 8.5; 5. Maximum: 70m below the static water table.Certificate Application Fields 1. Building/construction work/domestic water supply; 2. Irrigation and small water work; 3. Landscaping; 4. Water conservancy system; 5. Factory. Features 1. Edible oil filled motor, stable& reliable running with pressure regulating membrane; 2. Available with pump casing with plug, integrated stage floating impellers; 3. Installation in 6" or larger boreholes. Optional Available On Request No
Add to wishlist
Read more
Quick view
Close

6SS 6’’ Deep Well Pump

Performance Range
Max. Flow: 78m3/h Max. Head: 283m Application Limits 1. Max. ambient temperature < 40℃; 2. Sand content(in mass fraction)up to 0.01%; 3. hydrogen sulfide content up to 1.5mg/L, chloride ion content up to 400mg/L; 4. pH 6.5 to 8.5; 5. Maximum: 70m below the static water table. Certificate Application Fields 1. Building/construction work/domestic water supply; 2. Irrigation and small water work; 3. Landscaping; 4. Water conservancy system; 5. Factory. Features 1. Available with stainless steel pump head, effective against the corrosion and abrasive wear; 2. Edible oil filled motor, stable& reliable running with pressure regulating membrane; 3. Available with controller box, bring about general protection; 4. Installation in 6" or larger boreholes. Optional Available On chamber is available with 3"or 4"
Add to wishlist
Read more
Quick view